Facebook Twitter Instagram
    Today’s Machining WorldToday’s Machining World
    • Swarfblog
    • Podcast
    • Industry News
    • Videos
    • About
    • Advertise
    • Back Issues
      • Editor’s Notes
      • Featured Stories
      • Forum
      • How it Works
      • Lloyd Graff’s Afterthought
      • Reviews
      • Shop Doc
      • Interviews
      • Magazine Back Issues
    • Subscribe
    • Contact
    Today’s Machining WorldToday’s Machining World
    Home » Risk-Based Thinking for Job Shops: What ISO 9001:2026 Actually Asks You to Do
    Industry News

    Risk-Based Thinking for Job Shops: What ISO 9001:2026 Actually Asks You to Do

    Elena UlanovaBy Elena UlanovaNovember 17, 2026Updated:November 17, 2026No Comments7 Mins Read
    Facebook Twitter Pinterest LinkedIn Tumblr Email
    Share
    Facebook Twitter LinkedIn Pinterest Email

    “Show me how you handle risks and opportunities.” Few audit requests make a small shop owner more nervous. Many picture a thick risk register, color-coded heat maps and a consultant’s invoice. ISO 9001:2026, published in September 2026, asks for much less than that, and for something more useful.

    What changed from the 2015 edition

    The new edition keeps the same structure and principles: customer focus, the process approach, risk-based thinking and continual improvement. The changes are moderate. The ones a job shop will notice:

    • Risks and opportunities are now separate. Clause 6.1 is split into three parts: determining risks and opportunities (6.1.1), actions to address risks (6.1.2) and actions to address opportunities (6.1.3). Opportunities are no longer just a footnote to risk.
    • Quality culture and ethical behavior. Top management is now expected to promote them (clause 5.1), and people’s awareness of them is part of clause 7.3.
    • Climate change. The 2024 amendment is built in. You decide whether climate change is a relevant issue for your shop and whether your customers have requirements about it (clauses 4.1 and 4.2).
    • Planning changes. Changes to the quality system have to be planned and controlled (clause 6.3).
    • More guidance. An expanded Annex A explains the intent of the requirements.

    The transition for certified shops

    If you hold an ISO 9001:2015 certificate, you do not need to panic. Certified organizations have until September 30, 2029 to transition. It can happen at a scheduled surveillance or recertification audit, or at a separate transition audit. From March 31, 2028, new certifications will only be issued to the 2026 edition. Ask your registrar when it can audit to the new version, and plan the update into your next audit cycle instead of leaving it to the last year.

    What the standard actually asks on risk

    In plain words, clause 6.1 asks you to:

    • Look at your business and your customers (clauses 4.1 and 4.2) and decide which risks and opportunities could affect your ability to ship good parts and keep customers satisfied.
    • Analyze and evaluate them, then plan actions in proportion to their potential impact.
    • Build those actions into your normal processes.
    • Check whether the actions worked.

    A five-person shop is not expected to do what an aerospace prime does. No FMEA, risk register or scoring matrix is required by name. What an auditor will look for is evidence that you thought about what could go wrong and what could go right, acted on what matters, and know whether it worked.

    Where risk really lives in a machine shop

    You already manage risk every day. You just don’t call it that. When a machinist double-checks an offset on a new job, that is risk-based thinking. In many shops the real gap is that the rules live in people’s heads: “this is how we do it.” Instructions are spread across email, texts, sticky notes and hallway conversations, and nobody can say who approved a change or which drawing is current.

    For most job shops, the risk list is short and familiar:

    • A machinist running from revision 10 of a drawing when revision 12 is current.
    • A new material, supplier or heat treat source.
    • A first run on a new or rebuilt machine.
    • One person who is the only one who knows how to set up a critical job.
    • A tight-tolerance feature that is hard to measure.
    • A customer with special requirements buried in the PO terms.
    • A rush order that skips the normal review.

    Opportunities get their own list

    Under the 2026 edition, opportunities deserve their own short list, with their own actions and their own check. For a machine shop that might be a new customer in a growing industry, a machine that frees up capacity, a cross-trained second operator, or moving paper travelers and scattered records into one system. Write down what you will do about each one, who owns it, and how you will know it paid off.

    A one-page approach that works

    You do not need software or a consultant to meet clause 6.1. One page, reviewed a few times a year, is enough for many small shops.

    1. List what could hurt the customer or the business, and what could help it. Sit down with the owner, the lead machinist and whoever handles quality and purchasing. Spend an hour. What has gone wrong in the last two years? What almost went wrong? What could we do better or new?
    2. Pick the few that matter. Ask how likely it is and how much it would affect the part and the customer. Keep it to high, medium or low. Anything high on both gets an action.
    3. Tie each action to a process you already run. This is the step most shops skip. Put it where the work happens:
    • Revision changes: add a revision check to contract review and the traveler.
    • New suppliers: add an approval step before the first PO.
    • Single-person knowledge: schedule cross-training and write a setup sheet.
    • Hard-to-measure features: confirm gauge capability before the job is quoted.
    • Rush orders: define the minimum review that never gets skipped.
    1. Name an owner and a date. An action with no owner is a wish.
    2. Check if it worked. Look at your own data: NCRs, customer complaints, late deliveries, scrap. If revision errors stopped after you added the traveler check, write that down. If they didn’t, change the action.

    How to show it to an auditor

    A good two-minute answer sounds like this: “Here are the risks we decided to control and the opportunities we decided to pursue. Here is where each action lives in our process. Here is the owner. Here is what our data showed afterward.”

    Then show one example on the floor: the traveler with the revision check, or the setup sheet a second operator now uses. Review the page at management review and whenever something big changes: a new customer, a new machine, a key person leaving, or a nonconformance that surprised you.

    Common mistakes

    • Building a risk register no one opens. Twenty pages of generic risks copied from a template.
    • Listing risks with no actions. Identifying a risk is not the requirement. Acting on it is.
    • Actions that never reach the floor. If the machinist doesn’t know about the control, it doesn’t exist.
    • Treating opportunities as an afterthought. The 2026 edition gives them their own clause.
    • Never checking effectiveness. If you can’t say whether an action worked, the job isn’t finished.

    Start small this week

    Start with one meeting and one page. List five risks and three opportunities. Pick the top few, tie each to a process, and assign an owner. Look at the results in three months.

    Risk-based thinking is not a new system bolted onto your shop. It is the habit of asking “what could go wrong here, what could go better, and what are we doing about it?” and keeping the answer where people can see it. Most good shops already think this way. ISO 9001:2026 just asks you to show it.

    Want a second set of eyes? QMS2GO offers a free ISO 9001 gap analysis for small and mid-sized manufacturers at qms2go.com, or call (318) 200-0351.

    Elena Ulanova is co-founder of QMS2GO, an AI-enabled quality management platform that helps US small and mid-sized manufacturers achieve and maintain ISO 9001 certification. She holds a degree in Standardization, Certification and Metrology from Karaganda State Technical University, has published on risk-based thinking in ISO 9001:2015, and received the 2026 Best in Biz Awards International Bronze for Executive of the Year – Small Companies.

    Share. Facebook Twitter Pinterest LinkedIn Tumblr Email
    Elena Ulanova
    • Website

    Related Posts

    Talking Robot Integration with @Malachi Greb of Elite Automation, EP 203

    November 30, 2023

    Ep. 112 Developing a World-Class CNC Turning Company with Mike Reader

    September 7, 2023

    A Week to Remember

    January 31, 2023

    Comments are closed.

    Marubeni Citizen Cincom

    Join Email List

    Subscribe to the Swarfblog

    Lists*

    Facebook Twitter Instagram
    © 2026 Today's Machining World

    Type above and press Enter to search. Press Esc to cancel.